沿途的风景carry out = perform = conduct = execute catenary anchor leg mooring (CALM) 进行、执行 悬链锚腿系泊 charpy-V notch energy charpy-V notch impact test 夏比V形缺口韧性值 夏比V形缺口冲击试验 cathodic protection cellar deck
cellar shutdown panel (CSDP) cement grout cementing vessel center line center of buoyancy center of floatation center of gravity center punch
central control room (CCR) central processing platform centrifugal pump centrifuger ceramic fibres ceramic tiles certifying authority chain block chair with arm-rest chamfering channel steel
阴极保护 底甲板 井口系统关断盘 水泥浆 固井船 中心线 浮心 漂心 重心 冲子 中央控制室 中心处理平台 离心泵 离心机 防火陶棉 瓷砖
第三方检验机构 倒链
带扶手的半软椅 开坡口 槽钢
chart datum check randomly check valve checkered plate
chemical injection package chemical injection system chemical seal chipping hammer chisel chord member christmas tree circumference circumferential weld classification survey clean water injection pump clean water surge tank clearance client
close drain tank closed / open circuit closed drain pump
海图基准面 抽检 止回阀 花纹板 化学注入橇 化学注入系统 化学密封 敲渣锤 风铲 弦杆 采油树 周长 环焊缝 入级检验 清水注入泵 清水缓冲罐 间隙 业主、顾客 闭式排放罐 闭 / 开路 闭式排放泵
6
clustered well heads CO2 cylinder unit CO2 extinguisher coal tar epoxy paint coaming coating coating interval coefficient cold formed pipe cold shut cold work collapse ring column
combustible gas detector come-along
commercial blast cleaning commissioning
compile and maintain a document complete penetration groove weld completion riser complex joint compliance with comply with
丛式井口 CO2气瓶组 CO2灭火器 含焦油环氧涂料 挡水扁铁 涂装 涂漆间隔 系数 冷卷管 冷隔 冷加工、冷作 加强环板 立柱
可燃气体探测器 手扳葫芦 普通级喷砂除锈 调试
编制和保存文件 全熔透坡口焊 完井立管 复杂节点 符合（名词） 符合（动词）
composite rockwool ceiling composite rockwool panel concentric reducer conceptual design concrete platform condensate drum condensing water conductor conductor guide cone
conform to = stick to = adhere to connection consumption rate continuous beam
continuous double fillet weld continuous welding contract contraction stress contractor
control valve (accessories handwheel) control valve assembly coordinates coordination
复合岩棉天花板 复合岩棉板 同心大小头 概念设计 混凝土平台 冷凝液罐 冷凝水 隔水套管 套管导向 大小口、锥体 符合、遵守 节点、连接 阳极消耗率 连续梁 双面连续贴角焊 连续焊 合同 收缩应力 承包商 带手轮的控制阀 控制阀总成 坐标系 协调
7
cope hole
corrective and preventive action correlation curve corrosion allowance corrosion coupon corrosion protection corrugated plate interceptor couplant coupling crack
crane barge, crane vessel crane support crater crawler crane criteria cross angle cross section crow bar cruciform bollard crude cooler crude filter
crude heat exchanger crude loading /export pump
(焊接)工艺孔 纠正和预防措施 相关曲线 腐蚀余量 腐蚀挂片 防腐 斜板分离器 UT用的耦合剂 联轴器、管箍 裂纹 起重船 吊机支撑 焊口 履带吊车 (验收)标准 交叉角 横截面 撬杠 单十字带缆柱 原油冷却器 原油过滤器 原油换热器 原油外输泵
crude loading pump crude oil drain tank crude preheat exchanger
crude suction strainer crude transfer cup support curing time current capacity current density current direction curvature radius customer cut by torch cut off
cutoff allowance cutting plan cutting sheet
原油装载泵 原油排放舱 原油预热器
原油吸入滤器 原油输送泵 垫墩
（油漆的）固化时间 （阳极的）电流容量 （阳极的）电流密度 海流方向 曲率半径 客户 以火焰切割 割除、割除物 切割裕量 排板图 单件图
8
D
(in) duplicate (to) drive piles DAC curves daily diesel filter
damage-prone connection damper, dampener DC generator Decibel (dB) deck beam deck cover deck crane deck water seal unit deep freeze compressor deepwater jacket
defect /default /disconnection deflection
dehydration degassing vessel dehydration preheater dehydration feed pump delivery of materials derrick barge
一式两份 打桩
距离-振幅曲线 日用柴油滤器 易破坏的节点 减震器 直流发电机 分贝 甲板梁 甲板敷料 甲板吊车 甲板水封装置 深冷压缩机 深水导管架 缺陷 挠度 脱水除气器 脱水预热器 电脱水供给泵 材料交货 回转式起重船
desander
design basis design parameters detail detail design
develop / establish a document dew point
DFT (dry film thickness) diagonal brace dial gauge diaphragm diaphragm valve die stamp diesel daily tank diesel filter coalescer diesel generator set
diesel oil daily tank with heater diesel pump diesel storage tank
diesel storage tank with heater diesel tank diesel transfer pump
differential pressure control valve
除砂罐 设计基准 设计参数 详图 详细设计 编制文件 露点 干膜厚度 斜拉筋 百分表 隔板 隔膜阀 钢印 柴油日用罐 柴油过滤净化装置 柴油发电机组
柴油日用罐（带加热器）柴油泵 柴油储罐
柴油储罐（带加热器） 柴油罐 柴油输送泵 差压控制阀
9
diffuser dihedral angle dimensional checks
direct / alternating current arc welding direct current emergency supply disassembling discontinuity displacement oil tank distortion from welding distress signals diver
diver support vessel document approval and issue documentation dog dolphin
domestic sea water pump double agent facility double bed double bevel groove double bollard double groove double probe method
布风气 二面角 尺寸检查 直/交流电弧焊 直流应急电源 拆除 缺陷 置换油罐 焊接变形 遇险呼救信号 潜水员 潜水作业船 文件的批准和下发 文件编制 组装用的刀把 系缆柱 生活海水泵 双介质灭火装置 双层床 k形坡口 双柱带缆桩 双面坡口 双探头法
double V groove doubler plate down hill welding drain pit draught gauge
drawing and specification drawing types 图纸种类有： conceptual drawing basic drawing bid drawing design drawing fabrication drawing shop drawing as-built drawing dredger drift pin drift test drill
drilling module drilling platform drilling template drillship, drilling ship
双面V形坡口(X形) 垫板、包板 向下焊 排放池 吃水标尺 图纸及技术规格书 图纸种类
概念图纸 基本设计图纸 招标图纸 详细设计图纸 加工设计图纸 车间加工图纸 完工图 挖泥船 心轴、销子 管流试验、管线试通 钻头 钻井模块 钻井平台 钻井基盘 浮式钻井船
10
